Barium titanate lead-free piezoelectric
ceramics are important basic materials for the development of modern science
and technology, which was widely used in the manufacture of ultrasonic
transducers, underwater acoustic transducers, electroacoustic transducers,
ceramic filters, ceramic transformers, ceramic frequency discriminators, high
voltage generators, infrared detectors, surface acoustic wave devices,
electro-optic devices, ignition and detonation devices, and piezoelectric
gyroscope and so on.
Application: military, ocean, fishery, scientific research,
mine detection, daily life and other fields.
Piezoelectric Ring,Lead Free Piezoelectric Ring,Piezo Electric Ring,Lead Free Piezo Rings Zibo Yuhai Electronic Ceramic Co., Ltd. , https://www.yhpiezo.com
Taking a sample having a specific surface area of ​​1 m 2 /g as an example, the adsorption amount of 0.5 g of nitrogen to the sample is about 0.1 ml under the BET partial pressure range, and the volume under the liquid nitrogen temperature of the adsorption environment during the test is about 0.03 ml; The remaining volume (ie, the background volume) of the sample tube loading portion is about 3-5 ml. To accurately quantify the total adsorption amount of 0.03 ml in the sample tube volume of 3-5 ml and ensure the accuracy is less than 3%, it can be calculated. The accuracy of the pressure sensor is required to be above 0.03%; however, the accuracy of the best imported pressure sensor is only 0.1%, and the accuracy of the pressure sensor for the surface and aperture analyzer is usually 0.15%, which means that the highest precision pressure is currently available. The sensor, even if the temperature field is ideally determined, the liquid nitrogen surface is ideally constant, and the ambient temperature is ideally accurate. The uncertainty of the amount of adsorption can only reach 0.003ml, that is, the uncertainty reaches 10%; The small or small density of the sample is also a sample with a large amount of sample loading, and the accuracy can be imagined. However, for medium-large ratio surface samples, the general adsorption amount is not so small, and the accuracy of the static method is easily guaranteed to be within 2% or even 1%;
Therefore, in the test of small specific surface samples, the static method can only reduce the error by increasing the amount of sample loading. It is common that static is generally equipped with a large-capacity sample tube for small specific surface area samples, but due to the background volume (the volume of the adsorption chamber) Increasingly, the accuracy is also limited; and some manufacturers claim that the static method is less than the surface test limit of 0.0001m2/g, which is irresponsible;
For the high-precision dynamic method instrument with wind-heat assist, detector constant temperature and low-temperature cold trap, the accuracy of the standard dynamic method surface surface meter without the device is obviously improved; the dynamic method surface surface meter and other analysis Similar to the instrument, its accuracy and sensitivity mainly depend on the signal-to-noise ratio; that is, to improve the accuracy and sensitivity, it needs to be controlled from three aspects: improving signal strength, suppressing background noise, and eliminating external interference. The method of increasing the signal strength generally increases the sample weight and increases the detector current. However, increasing the detector current generally increases the noise at the same time, so the detector current has an optimal range; therefore, in suppressing noise and eliminating external interference. The work that can be done is much more; the source of error originating from the instrument itself is: detector temperature drift, signal sharpness; the detector thermostat is used to suppress temperature drift, and the wind-heat assist device can improve signal sharpness. For the sample with a surface area of ​​1 m 2 /g of 0.5 g of nitrogen adsorption amount at a partial pressure of about 0.2, the peak area and background can be guaranteed to be within 2%;
Therefore, for small surface samples, the advantages of sensitivity and resolution for dynamic instrumentation with wind-heat assist, detector constant temperature, and low-temperature cold trap are reflected; however, for medium-to-large ratio surface samples, due to strong signal, Both the normal dynamic surface area meter and the static surface area meter ensure accuracy; this is like the difference between one-tenth of an analytical balance and a thousandth of a balance;
However, most materials containing voids such as micropores and mesopores are not much smaller than the surface; if the material is smaller than the surface, the research value of the void fraction is limited;
In summary:
1. For small surface samples (below 10m2/g), the dynamic chromatography specific surface instrument with wind-heat assisted and detector thermostat is preferred, and its resolution and sensitivity are utilized.
Second, for medium-to-large ratio surface samples, if only the specific surface area is tested, the dynamic method and the static method have no obvious advantages and disadvantages. The dynamic method has the advantage of quickly determining the specific surface due to the solid standard reference method, and the static method has more BET. The point method is less advantageous than the time-saving liquid nitrogen consumption;
Third, the need to measure the surface and pore size distribution of the sample, it is recommended to use the static volume method of the specific surface and aperture analyzer;
December 09, 2022