In this paper, the model and analysis of the semiconductor laser temperature control circuit for communication equipment are carried out, and the detailed performance index analysis and test of the temperature control circuit form are carried out from the perspective of automatic control. Through the simulation analysis of different control methods and The comparison of the measured data shows a more effective temperature control circuit that can meet the requirements of the general temperature control system. In the field of optical fiber communication, a semiconductor laser is usually used as a light source, and the emission wavelength of the semiconductor laser is closely related to the temperature of the die, and the temperature rise will cause the wavelength to become longer (generally 0.1 nm ° C) for a general single-wavelength optical communication system. In other words, the drift of the wavelength does not have much impact on system performance. However, for Dense Wavelength Division Multiplexing (DWDM) systems, since the wavelength spacing between channels is already small, it is important to maintain wavelength stability. For example, a 32-wave system operating in the C-band has a path wavelength interval of 100 GHz (about 0.8 nm), while a 160-wave system operating in the C+L band has a path wavelength interval of 50 GHz (about 0.4 nm). Therefore, if the temperature of the laser die is not controlled, a small temperature change will result in the unavailability of the entire system. In addition, semiconductor lasers are temperature-sensitive devices, and their threshold current, output wavelength, and output optical power stability are all very sensitive to temperature, and their working life is closely related to their operating temperature. Experiments have shown that the lifetime of a laser can be reduced by an order of magnitude for every 30 °C increase in temperature. For high reliability requirements, and to ensure the life of the laser, it is necessary to control the temperature of the die, so that an automatic temperature control circuit (ATC) is needed in the system to control the temperature of the laser die. Figure 1 is a block diagram of a typical temperature control system. The sensor compares the measured actual temperature value with the set temperature value to obtain an error signal. The error signal is sent to the controller and drives the actuator to adjust the temperature. The role of the entire system is always stable at the set value. In optical communication systems, there are generally two types of light sources that require temperature control. One type is a laser used as a communication light source, and the other is a pump laser. In both types of optical devices, a thermistor and a thermoelectric cooler (TEC:) for forming a temperature control circuit are usually integrated. Performing cooling or heating). Then, the peripheral circuit needs to complete the amplification of the temperature detection signal, and after the appropriate controller circuit, the TEC refrigerator is driven by the power amplifier to complete the temperature control process. Therefore, the main links of the temperature control circuit are: The temperature signal detection amplifying circuit, the controller circuit, and the power amplifying circuit and the like. Generally, a common structure with a refrigerating laser is to first mount a laser, a backlight, a thermistor, and the like on a sub-heat sink, and then fix it to the TEC refrigerator. When the temperature control circuit works normally, it is located on the TEC. The sub heat sink will be constant at a certain set temperature value. When the TEC cooler is energized with different polar currents, it can be separately cooled or heated, and the temperature will not be abrupt, whether it is in a cold or a hot state, but a slowly changing process. At a certain current, when the time is long enough, the external heat exchange reaches an equilibrium state, and the temperature is maintained at a certain value (ie, a constant temperature difference ΔT from the casing). Therefore, it can be inferred that the TEC cooler is similar to the first-order inertia link in the transfer function model. In order to determine Ktec and Ttec, a constant current is used as the TEC refrigerator input, and the temperature is detected by the thermistor, and the collected temperature is obtained. The relationship with time is drawn by computer to get the corresponding curve. Taking the FLD5F6CXF of the laser FUJITSU as an example, after measuring Ttec for 6 seconds, Ktec can take 90, that is, the temperature difference of 1 amp current can be about 90 °C. Since there is a certain distance between the TEC refrigerator and the temperature sensor, the temperature delay time caused by the distance needs to be considered. The thermal delay time t of the measured FUJITSU laser is about 100 milliseconds. Due to the delay, This is equivalent to adding a delay link to the control loop. 200*300mm Anti-Blue Light Film
The Imported Anti-Blue Light For ipad is made of high-quality imported TPU material. It is precisely cut by the Screen Protector Cutting Machine. Protect your device screen from scratches and cracks. The flexible TPU Screen Protector can completely cover the iPad screen, providing the maximum protection for the iPad.
Advanced blue light blocking technology can protect your eyes, can effectively filter blue light, prevent glare, reduce eye fatigue, and help you fall asleep better.
Super clear and transparent, will not reduce the screen brightness, maintain the original screen brightness, and reduce eye fatigue.
The Protective Film adopts an oleophobic and waterproof coating, which can ensure anti-fingerprint, waterproof, dustproof and no air bubbles. Moreover, it is sensitive to touch, bringing natural touch, fast response and flawless precise touch.
If you want to know more about Imported Anti-Blue Light For ipad products, please click product details to view the parameters, models, pictures, prices and other information about Imported Anti-Blue Light For ipad products.
Whether you are a group or an individual, we will try our best to provide you with accurate and comprehensive information about Imported Anti-Blue Light For ipad!
Imported Anti-Blue Light Protective Film, Imported Anti-Blue Screen Protective Film, Imported Anti-Blue Screen Protector, Imported Anti-Blue Light Screen Protector Shenzhen Jianjiantong Technology Co., Ltd. , https://www.hydrogelprotectivefilm.com
March 11, 2023